The network techs vision into cabling bandwidth
CableIQ qualification tester is the first cabling bandwidth tester for network technicians. This Ethernet network cable testergives even the most novice tech the vision to see what speeds existing cabling can support, quickly isolate cabling from network problems, and discover what is at the far end of any cable. That means network techs can close trouble tickets faster, reduce on-call time, and save money by better utilizing their existing infrastructure.
Reduce escalated problems by as much as 30%
CableIQ qualification testers powerful network troubleshooting capability and intuitive interface enable your frontline technicians to identify and troubleshoot a wider range of problems within your network infrastructure. Is the port active? Are the duplex settings matched? Is it a network problem or a Ethernet cable problem? Can the Ethernet cable support the required network bandwidth? CableIQ network analyzer is the only Ethernet cable tester that can answer all these questions before trouble tickets are escalated to the next level reducing problem escalation by up to 30%.
When you deploy Voice over IP (VoIP) or Gigabit Ethernet, you want to make sure that the existing cabling will support the bandwidth requirements of your new equipment. Your cabling was certified, but moves adds and changes have rendered many links incapable of running desired speeds. CableIQ quickly reveals whether a link, including patch cords, is qualified for voice, 10/100BASE-T, VoIP, or Gig. Knowing your cablings bandwidth capabilities before upgrading can prevent countless hours of future downtime and labor hours wasted on unnecessary troubleshooting.
Plug into any cable, patch panel, or wall jack and see both the cable details (length/wiremap) and far-end device details (speed/duplex settings) at once. A series of both cable and network test functions help you isolate connectivity problems. For instance, if Discover mode shows duplex settings are matched but the problem persists, run Autotest to see if the cabling can support the required bandwidth. If a link is not qualified, CableIQ provides detailed information on the nature and location of cabling performance faults such as crosstalk or large impedance changes. With CableIQ your techs can close trouble tickets faster by cutting cable troubleshooting time in half.
|
General Specifications |
|
|
Cable types supported |
UTP, STP, FTP, SSTP, RG6, RG59, audio
and security |
|
Qualification autotests |
1000BASE-T, 100BASE-TX, 10BASE-T,
VoIP, 1394b S100, TELCO, Wiremap only, Coax |
|
Supported tests |
Wiremap, length, cable signal
performance, digital toner, analog toner, Ethernet port detection and
identification, analog telephone detection, blink port light, continuity,
speaker test, cable fault finding, video signal detection. |
|
Wiremap |
Can detect single wire faults and
supports MultiMap mode with up to seven remote office identifiers. Draws
proportional wire length to breaks. Detects split pairs. |
|
Find fault |
Measures crosstalk and impedance and
compares against appropriate limits based on qualification test selected.
Detects location of large point sources as well as distributed sources in the
cabling if they are sufficient to disqualify the application |
|
Results storage |
Up to 250 qualification test results |
|
Power |
Battery type: 4 AA (NEDA 15A, IEC
LR6) alkaline batteries |
|
Battery life |
20 hours of typical use, without
backlight |
|
Other battery types supported |
4AA photo lithium, NIHM, NICAD |
|
Dimensions and weight |
7in x 3.5in x 1.75in (17.8cm x 8.9cm
x 4.5cm) 1.2 lb (0.55 kg) |
|
Models |
|
CIQ-FTKSFP |
|
CIQ-100 |
|
CIQ-KIT |
|
CIQ-KRQ |
|
Accessories |
|
CIQ-IDK24 |
|
CIQ-IDK57 |
|
CIQ-RJA |
|
CIQ-COAX |
|
MICRO-DIT |
|
CIQ-SPKR |
|
CIQ-WM |
|
MT-8200-63A |