This easy-to-use, competitively priced tester is three tools in one—a cable fault locator, a cable & wire manager and a tone generator with SmartTone technology.
From just ONE END of any two or more conductor cable you can measure up to 3,000 feet (915 meters). The TS 100 cable fault locator lets you easily find the distance to opens or shorts on electrical wire, telephone wire, security wire and coax. Results appear as a distance reading rather than a waveform, so its perfect for technicians unfamiliar with Time Domain Reflectometery (TDR) fault locator.
Locate and fix cable fault problems without pulling new wire or blindly cutting into walls. Intermittent faults are easier to find because the cable fault locator unit constantly measures while On.
The TS 100 cable fault locator is perfect for inventory management of cable stock in trucks and warehouses and it can help you generate more accurate bids for jobs by quickly assessing needs and managing the cable stock with greater accuracy.
The TS 100 cable fault locator with patented SmartTone technology gives you 5 distinct tones to use for exact wire and pair identification, even in proximity to current-bearing cable.
When touching the wires together and momentarily shorting the far end of a cable pair, the SmartTone technology will change the cadence of the tone generated. This tone change you hear through the probe positively verifies the correct wire pair.
Voltage detection in the cable fault locator unit will immediately sound an alarm if you accidentally clip onto an energized pair, up to 250VAC.
An easy-to-use cable fault locator, cable and wire manager and tone generator.
|
General Speciffications |
|
|
Power |
4 AA alkaline batteries, provide 50
hours of operation. |
|
Reverse Battery Protection |
No damage to the tester will occur if
the batteries are installed backwards. |
|
Input Protection |
250 V rms ac, continuous or
intermittent |
|
Moisture |
If the tester is exposed to water,
some may get inside, but it will suffer NO DAMAGE. See the information on
moisture under Maintenance. |
|
Impedance Range |
35 Ω to 330 Ω with auto-compensation
within this range. Cables with an impedance outside this range will not be
properly tested and may produce erratic or incorrect readings. |
|
Maximum Length |
2500 feet on certain cable types,
2000 feet on most cable types, and 500 feet on very lossy cables. The tester
will display –Err if the cable is too long to be correctly measured. |
|
Representative Maximum Cable Length |
2500 feet: CAT-5 Twisted Pair 2000
feet: 12/2 ac Wire 1000 feet: RG-6/U TV Coax 500 feet: RG-174/U Coax |
|
Minimum Length |
No minimum length Minimum non-zero
reading is 2 feet |
|
Length Accuracy |
±2 feet for cables less than 10 feet
±5 feet for cables longer than 10 feet and shorter than 200 feet ±3 % and ±5
feet for cables longer than 200 feet |
|
High Voltage Detection |
An ac voltage of more than 5 V rms
will trigger the High Voltage Warning. |
|
Measurement Rate |
Maximum of 4 complete measurements
per second, decreasing to 2 seconds per measurement based on cable size and
uniformity. |
|
VOP |
Adjustable from -20- to -99-,
retained during power off. Default to -66- when batteries are changed |
|
Measurement Technology |
Time Domain Reflectometry (TDR) with
50 Ω drive impedance, 6 V maximum pulse height |
|
Tone Injection |
Approximately 1 kHz at an amplitude
of 80 % of battery voltage. Variable frequency and cadence. Tone
characteristic is changed as cable condition changes to “normal-open” from
any other condition. |
|
Cable Type |
Virtually all two or more conductor
cables |
Models
26500000
26500500
26500610
26500390
Accessories
26501160
26501200
26501700
26501600
26501100
